Euronaval 2026 – FN launches its M3M Endurance 12.7 mm machine gun and shows some new items under development
Pre-launched at AUSA in mid-October, the M3M Endurance, the FN® 12.7 mm machine gun has been officially unveiled at Euronaval 2026 in Paris. While retaining the same footprint of the M3, the new weapon has a major advantage over its predecessor, the much lesser need of maintenance, something always welcome by operators. Plus, a longer operational life
click on image to enlargeWhy FN decided to evolve its M3 into the M3M Endurance? The original M3 had a series of advantages compared to the M2, the main one being a much higher rate of fire; while the M2 cycling rate of fire was between 485 and 635 rounds per minute, the M3 had nearly twice that rate, up to over 1,100 rpm. While the M2 was born for manual operations and was a typical always-working weapon, the M3 was a much finer weapon, born to be used on helicopters, naval vessels, and in remotely controlled weapon stations, however it required more maintenance. Some services were already used to programmed maintenance cycles, other less, and this proved to be an issue. Making it a weapon that needed less maintenance while keeping all its advantages over legacy 12.7 mm machine guns was therefore the task for FN engineers in the last few years.
click on image to enlargeThe M3M Endurance maintains the same 1,100 ± 100 rounds per minute firing rate, the same short recoil open bolt operating system, but has much less maintenance. “In the previous model we had a major maintenance every 5,000 rounds, while now we have one every 15,000 rounds. Moreover, we have extended the life of the weapon, from 40,000 to 60,000 rounds,” an FN representative told EDR On-Line.
This was obtained working on points that were weaker, as well as on materials, treatments, and simplified mechanisms. The main visible difference lies in the rear block, which is shorter. In the M3M Endurance the rear block has no maintenance and is replaced after 15,000 shots, the same being true for the slide. Overall, the PRP (Periodic Replacement Part) kit is made of nine components. In the past two different kits were needed, one for maintenance after 5,000 rounds and another after 10,000, a single kit at a higher number of rounds making maintenance easier. In fact, with only three major maintenance events, the weapon attains the 60,000 rounds end of life. Feeding can be right or left, it uses M9 links, and it has a mass of around 37 kg.
click on image to enlargeWhile the M3M Endurance was shown for the first time, looking closely at its fitting we could find a few items that are still under development at FN, for which Euronaval was an anticipation. At the Paris exhibition the new development of the 12.7 mm machine gun was presented in a counter UAS role, which included a new mount and a new aiming system. The M3M Endurance was fitted, together with an M3 Legacy, on a dual mount, which EDR On-Line understood it is referred to as the 2M3; this is for the time being a proof of concept, another dual mount being under development for 7.62 mm machine guns such as the MAG or the Minimi (in both 7.62- and 5.56-mm calibres). Installing two weapons allows increasing hit probability with double firepower, a key factor when using them as last-ditch defence against drones and maximizes value from existing inventories of combat-proven machine guns.
Another development item could be seen looking closely at the aiming suite. This was built around the DCL-120, a red dot reflex sight with extra wide lens providing an unlimited field of view with both eyes open. On top of this was fitted an FN Elity Lite laser rangefinder, while on the left we could see the FN Victor, a C-UAS solution still in the development phase, which assists the gunner while tracking the target, a crown of red LEDs located along the visor perimeter lighting up when maximum kill probability is attained, the weapon being on target, the latter being within range.
click on image to enlarge
click on image to enlargeThis shows well how much FN is engaged in adding new solutions to C-UAS systems. Talking about dedicated 12.7×99 mm ammunition dedicated to the C-UAS role, EDR On-Line understood that also in the field of fragmented rounds some developments are ongoing in Belgium. Currently C-UAS ammunition in that calibre are available from Swiss P of Switzerland and MKE of Turkey. Compared to the declared effective range of the M3M Endurance, which is around 2.5 km, when those fragmented ammunition is used range decreases, however the probability of hitting and destroying the drone increases considerably. To get more details on new mounts and aiming solutions by FN we will have to wait one of the 2027 defence exhibitions.
Photos by P. Valpolini, graphics courtesy FN
Content preview only. Full article available at source. View Full Article
FN Herstal unveiled the M3M Endurance 12.7 mm machine gun at Euronaval 2026 in Paris, highlighting its reduced maintenance needs and extended operational life. The weapon maintains a firing rate of 1,100 rounds per minute and introduces new developments for counter-UAS roles, including advanced aiming systems and dual mounts for increased firepower. The event showcased FN's commitment to enhancing military capabilities in drone defense.
- The M3M Endurance machine gun has a firing rate of 1,100 ± 100 rounds per minute.
- Maintenance intervals have increased from every 5,000 rounds to every 15,000 rounds.
- The operational life of the weapon has been extended from 40,000 to 60,000 rounds.
- New developments for counter-UAS roles were showcased, including a dual mount system and advanced aiming solutions.
- FN is engaged in developing fragmented rounds for C-UAS applications.